-
1 образование трещин в свежеуложенном бетоне
Construction: plastic crackingУниверсальный русско-английский словарь > образование трещин в свежеуложенном бетоне
-
2 образование трещин вследствие пластической усадки
Silicates: plastic crackingУниверсальный русско-английский словарь > образование трещин вследствие пластической усадки
-
3 благодаря
•is chosen for consistency with...
•Illumination periods are increased through the presence of an atmosphere.
•Hydrogen iodide, by virtue of (or because of, or owing to) its capacity to reduce... always adds in the normal manner.
•These materials are used mainly for their refractive properties.
.благодаря... можно благодаря... можно успешно применять благодаря... стало возможно получить благодаря которому происходит* * *Благодаря (не путать с предлогом "за счёт") -- because of, by virtue of, as a benefit of; due to, owing to, thanks to; by, for, throughMolded plastic gearing is presently in wide use because of relatively low cost.A material may be cracking at an accelerated rate by virtue of a creep-fatigue interaction.Note that, as a benefit of the nondimensionalization, complete information is contained in a pair of curves.In these steels both the Type II MnS and Al2O3 galaxies are prevented from forming through desulfurization and inclusion shape control. (... благодаря десульфуризации и контролю формы включений)Русско-английский научно-технический словарь переводчика > благодаря
-
4 трещинообразование при пластической осадке
Construction: plastic settlement crackingУниверсальный русско-английский словарь > трещинообразование при пластической осадке
-
5 трещинообразование при пластической усадке
Construction: plastic shrinkage crackingУниверсальный русско-английский словарь > трещинообразование при пластической усадке
См. также в других словарях:
Plastic lumber — (commonly abbreviated as PL) is a 100% recyclable material lumber or timber made of recycled plastic.There are also applications in the market, which utilize only virgin raw materials. Its most widespread use is in outdoor deck floors, but it is… … Wikipedia
Plastic moulding — In Plastic moulding, the moulding process selected depends upon two main factors: The geometry of the component to be moulded and the material from which it is to be made. There are two main groups of plastic moulding materials: Thermoplastic… … Wikipedia
Environmental stress cracking — (ESC) is one of the most common causes of unexpected brittle failure of thermoplastic (especially amorphous) polymers known at present. Environmental stress cracking may account for around 15 30% of all plastic component failures in service.H. F … Wikipedia
Wood-plastic composite — (commonly abbreviated as WPC) is a non recyclable composite material lumber or timber made of recycled plastic and wood wastes. There are also application in the market, which utilize only virgin raw materials. Its most widespread use is in… … Wikipedia
Polyoxymethylene plastic — Polyoxymethylene (POM), in the USA also commonly known under DuPont s brand name Delrin, is an engineering plastic, a polymer with the chemical formula ( O CH2 )n . It is often marketed and used as a metal substitute. Delrin is a lightweight, low … Wikipedia
Reinforced concrete — is concrete in which reinforcement bars ( rebars ), reinforcement grids, plates or fibers have been incorporated to strengthen the concrete in tension. It was invented by French gardener Joseph Monier in 1849 and patented in 1867.[1] The term… … Wikipedia
industrial polymers, major — Introduction chemical compounds used in the manufacture of synthetic industrial materials. In the commercial production of plastics, elastomers, man made fibres, adhesives, and surface coatings, a tremendous variety of polymers are… … Universalium
List of pipeline accidents — The following is a list of pipeline accidents: This is an incomplete list, which may never be able to satisfy particular standards for completeness. You can help by expanding it with reliably sourced entries. Contents 1 Bel … Wikipedia
Plasterwork — refers to construction or ornamentation done with plaster, such as a layer of plaster on an interior wall or plaster decorative moldings on ceilings or walls. This is also sometimes called pargeting. The process of creating plasterwork, called… … Wikipedia
Properties of concrete — Concrete has relatively high compressive strength, but significantly lower tensile strength, and as such is usually reinforced with materials that are strong in tension (often steel). The elasticity of concrete is relatively constant at low… … Wikipedia
Concrete — This article is about the construction material. For other uses, see Concrete (disambiguation). Outer view of the Roman Pantheon, still the largest unreinforced solid concrete dome.[1] … Wikipedia